|
|
|
|
|
|
Camera cable connector
|
|
Our Price: $2.50
|
|
|
This cable features a 3 pin housing to connect into a camera on one side and a 3 pin female connector on the other end.
Cable length: 26cm.
|
|
|
|
|
|
|
|
|
|
Video transmitter cable connector
|
|
Our Price: $3.00
|
|
|
This cable features a 4 pin connector for your transmitter, and three different connection inputs for video, audio and power respectively.
Cable length: 30cm. video and audio cables, 15 cm transmitter power cable.
|
|
|
|
|
|
|
|
|
|
Camera "L" shaped cable connector
|
|
Our Price: $3.25
(4)
|
|
|
This cable features a right-angle connector with audio and video connections. This cable is compatible with GoProTM cameras for use with your FPV systems. Perfect for connecting your camera to an OSD or straight to your video transmitter.
Cable length: 30cm.
Pinout:
Yellow: Audio
Brown: Ground Red: Power Orange: Video
To connect to a GoProTM camera the red wire does not need to be connected. GoProTM does not take power from its video out line. |
|
|
|
|
|
|
|
|
|
Anti-Vibration spacer, M3 x 8mm
|
|
Our Price: $6.60
(1)
|
|
|
Anti-Vibration Spacers, M3 x 8mm
If you have vibrations on your camera, flight controller or other electronics. These are good rubber spacers for you.
Due to their elastic features, these spacers will dampen a lot of vibrations that can affect your electronics.
Technical specs: - Size: M3 x 8mm
- Outside dia: 12mm
- Length: 8mm
Includes: |
|
|
|
|
|
|
|
|
|
|
|
Anti-Vibration spacer, M3 x 12mm
|
|
Our Price: $8.00
(1)
|
|
|
Anti-Vibration Spacers, M3 x 12mm
If you have vibrations on your camera, flight controller or other electronics. These are good rubber spacers for you.
Due to their elastic features, these spacers will dampen a lot of vibrations that can affect your electronics.
Technical specs: - Size: M3 x 12mm
- Outside dia: 12mm
- Length: 12mm
Includes: |
|
|
|
|
|
|
|
|
|
|
|
jDrones custom low noise 5V/3Amp tested uBEC
|
|
Our Price: $8.50
|
|
|
jDrones Low noise 3A / 5V uBEC
This is custom made uBEC for jDrones. We made it extra silent, it's ripple current even close to maximum usage is kept really low.
Perfect to supply clean power to your APM! No more brownout from the motor ESC uBec, this is the definitive solution!
Technical Specs: - Output: 5V / 3Amp
- Input: 6 - 28V
- Size: 11 (W) x 26 (L) x 9mm (H)
|
|
|
|
|
|
|
|
|
|
|
|
Moon Gel (4 pads)
|
|
Our Price: $9.99
|
|
|
Moon Gel ! This is the best vibration absorption material.
|
|
|
|
|
|
|
|
|
|
|
|
jD-IOBoard v1.0, MCU controlled IO Board for driving LEDs, Relays, Servos
|
|
Our Price: $17.99
|
|
|
The wait is over! in stock now.
If you need to drive LED strips, LEDs, Lamps, Relays or similar devices jD-IOBoard is the answer for your needs. This board is fully Arduino compatible board and it has 6 high power outputs and can handle all the way 42 Volts and 500mA / output pin.
Board have easy access to FTDI / UART and I2C ports. Among high power outputs there are several TTL level GPIO pins and Analog pins. |
|
|
|
|
|
|
|
|
|
APM Power Module with XT60 Connectors
|
|
Our Price: $25.99
(1)
|
|
|
APM 2.5 Power Module
The APM 2.5 Power Module is a simple way of providing your APM 2.5 with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable. The on-board switching regulator outputs 5.3V and a maximum of 2.25A from up to a 4S LiPo battery. The Power Module comes completely assembled with XT-60 connectors, and wrapped in shrink tubing for protection.
|
|
|
|
|
|
|
|
|
|
CMOS Video Camera - 640x480 (FPV)
|
|
Our Price: $35.00
|
|
|
Why pay $99 for another camera if you can get this high-quality color CMOS module for a lot less? Easily mountable and has a wide operating voltage (5V to 15V), comes with high quality optics, all the on board circuitry to output RCA signal, and a cable harness.
Thoroughly tested on FPV system (even at night!) and capable of handling brutal crashes!Weight: 0.5 oz; 15 g Features 5V to 15V input. 50mA (at 12V). Switchable NTSC and PAL output using a jumper. 420 lines. Full spec sheet
|
|
|
|
|
|
|
|
|
|
jDrones MiniOSD
|
|
Our Price: $63.99
(1)
|
|
|
jD-MiniOSD v1.0
Fully MinimOSD compatible OSD with switching DC/DC stepdown powersupply to maximize efficiency on power system. No more heating problems when using this OSD board.
Boards are fully compatible with original 3DRobotics MinimOSD.
|
|
|
|
