Additional Options


Proud sponsor of 

Proud sponsor of
Click for the BBB Business Review of this Hobby & Model Construction Supplies - Retail in Mississauga ON
Home > Flight Controller / Autopilot
Choose a sub category:
DJI Flight controller 3DRobotics
PX4
Sort By:
Page of 1
APM2.5 Filter PCB. Rev.A
APM2.5 Filter PCB. Rev.A
Our Price: $4.99

APM2.5 Filter PCB, Rev.A

Dont want a full case for your APM 2.5?  
Is your barometer fully exposed and you don't know how to cover it properly. 
With APM25 Filter PCB this is done in easy way for you. Just connect filter PCB to existing pins and your barometric sensor will get covered by foam.

Includes:
  • 1 * APM2.5 Filter PCB
  • 2 * 2x3 Pin header connector, female
  • 1 * 2x3 Pin header connector, male
Instructions: Look jDrones/jDoc

*** Cannot be used at the same time as the case. 
APM 2.5 Case
Ardupilot Mega 2.5 Case (Side Pins)
Our Price: $5.99

(2)

This is the official case for the APM 2.5 system.  It's designed to keep your electronics safe while looking great at the same time!
The new APM 2.5 enclosure is made of black translucent ABS plastic. It protects your electronics while allowing access to all pins and connectors. The inside of the enclosure is lined with ESD safe open cell foam to ensure the barometric pressure sensor is surrounded by static air and prevent unwanted readings due to airflow over the sensor. The screws that secure the enclosure have been moved to the top for ease of use. 

The enclosure comes in two variants straight pins and angled pins. 
The side entry variant protects the I/O pins to protect them in the even of a crash.

This option is for the SIDE entry case, depending on your current APM 2.5 set up.



NOTE: This product is compatible with APM 2.5 only! The ArduPilot Mega 2.5 board is not included, it's included in the image only as a reference. 

Anti-Vibration spacer, M3 x 8mm
Anti-Vibration spacer, M3 x 8mm
Our Price: $6.60

(2)


Anti-Vibration Spacers, M3 x 8mm

If you have vibrations on your camera, flight controller or other electronics.
These are good rubber spacers for you.

Due to their elastic features, these spacers will dampen a lot of vibrations that can affect your electronics.

Technical specs:
  • Size: M3 x 8mm
  • Outside dia: 12mm
  • Length: 8mm
Includes:
  • 4 pcs in one bag
Anti-Vibration spacer, M3 x 12mm
Anti-Vibration spacer, M3 x 12mm
Our Price: $8.00

(1)


Anti-Vibration Spacers, M3 x 12mm

If you have vibrations on your camera, flight controller or other electronics. 
These are good rubber spacers for you. 

Due to their elastic features, these spacers will dampen a lot of vibrations that can affect your electronics.

Technical specs:
  • Size: M3 x 12mm
  • Outside dia: 12mm
  • Length: 12mm
Includes:
  • 4 pcs in one bag
5V/3Amp uBEC tested
jDrones custom low noise 5V/3Amp tested uBEC
Our Price: $8.50

(8)


jDrones Low noise 3A / 5V uBEC (switching regulator)

This is custom made uBEC for jDrones. We made it extra silent, it's ripple current even close to maximum usage is kept really low.

Perfect to supply clean power to your APM! No more brownout from the motor ESC uBec, this is the definitive solution!

Technical Specs:
  • Output: 5V / 3Amp
  • Input: 6 - 23V (will tolerate 6S for short duration but is not recommended for prolonged use)
  • Size: 11 (W) x 26 (L) x 9mm (H)
Moon Gel (4 pads)
Moon Gel (4 pads)
Our Price: $9.99


Moon Gel !  This is the best vibration absorption material.  




LM2596 4-40V to 1.25-37V DC -No Display
LM2596S 4-40V to 1.5-35V DC Converter Step Down Adjustable Regulated
Our Price: $15.00

(1)

LM2596 Buck Converter (No Display)

Lighter than it's big brother it can be used when you do not need to see the voltage.


HMC5883 Magnetometer for APM2.6
Our Price: $16.99


APM2.6 External Compass

This is a custom made 3-axis digital compass board based on the Honeywell's HMC5883L for APM2.5+ and especially for APM2.6 boards.  
LM2596 4-40V to 1.25-37V DC
LM2596 4-40V to 1.25-37V DC Converter Step Down Adjustable Regulated+Volt Meter
Our Price: $19.99

(1)

LM2596 Buck Converter+Voltmeter
  • Cutting Size: 66.04mm x 35.05mm
  • Input Voltage: DC 4.0~40V
  • Output Voltage: 1.25V~37V
AttoPilot Voltage and Current Sense Breakout - 90A
AttoPilot Voltage and Current Sense Breakout - 90A
Our Price: $22.00

(2)

Description: This is a small voltage and current sense PCB. DC current is determined by measuring a voltage drop across a pair of parallel 1 mOhm shunt resistors, then converted to a final analog voltage output by the TI INA-169. Voltage sense is accomplished by scaling to 3.3V ADC range by a precision resistor divider.

The PCB is supplied without leads or connectors. The pad sizes are large enough to accommodate 12 gauge heavy duty leads (see datasheet) but care must be exercised in soldering. Smaller gauge leads are considerably easier to solder without creating shorts.
Universal Foldable GPS/Compass Isolation Kit
Universal Foldable GPS/Compass Isolation Kit
Our Price: $22.00

After market 3D printed wide and high landing gear set.
Get more ground clearance with these legs.  Also have handy velcro holes in the upper portion to strap external LiPo to your Phantom.
Includes Compass mount on the leg and fits right where the original legs are bolted..
Universal Foldable GPS/Compass  Kit
Universal Foldable GPS/Compass mast
Our Price: $22.00

(7)

This is the very nice addition to the GPS accessories lineup.
Mount your GPS/Compass on that foldable arm to isolate it from interference.
Aluminium base and top, Carbon fiber rod
Unscrew the base joint and fold it over. Very convenient and easy to use.
APM Power Module
APM Power Module with XT60 Connectors
Our Price: $25.99

(7)

APM 2.5 Power Module

The APM 2.5 Power Module is a simple way of providing your APM 2.5 with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable. The on-board switching regulator outputs 5.3V and a maximum of 2.25A from up to a 4S LiPo battery. The Power Module comes completely assembled with XT-60 connectors, and wrapped in shrink tubing for protection.
Pixhawk Peripheral Kit
Pixhawk Peripheral Kit
Our Price: $25.99

(1)

This kit includes external LED and USB modules to connect to Pixhawk.
Use the provided four-position DF13 cables and connect to the I2C splitter module to set up a bright, multicolor LED and convenient USB port for your vehicle.


PPM Encoder
PPM Encoder
Our Price: $29.99

(6)

Our new PPM encoder allows you to connect your PWM-only RC equipment to PPM-only autopilot systems, like Pixhawk. Smaller than our previous PPM, our encoder will enable you to reduce all your channels to a single wire, excluding ground and power wires. As a result, you’ll get faster processing and reduced points of error.

APM 2.6
Latest ArduPilot Mega 2.6 - Assembled (SIDE PINS - NO compass)
Our Price: $179.00

This is the LATEST APM version available from 3DRobotics, no clones or cheap stuff!

APM 2.6 Kit (NO GPS version)

SIDE PINS

This new presentation of the ArduPilotMega 2.6 system features all the same goodies as the predecessor, same CPU, same memory, same case, power module... but it comes without magnetometer on the main board (compass)

Pixhawk
Pixhawk
Our Price: $225.00

(9)

Pixhawk is an advanced autopilot system designed by the PX4 open-hardware project and manufactured by 3D Robotics. It features advanced processor and sensor technology from ST Microelectronics® and a NuttX real-time operating system, delivering incredible performance, flexibility, and reliability for controlling any autonomous vehicle.

APM 2.6
Latest ArduPilot Mega 2.6 - Assembled (SIDE PINS - External compass)
Our Price: $265.00

(10)

This is the LATEST APM version available from 3DRobotics, no clones or cheap stuff!

APM 2.6 Kit (includes uBlox GPS with onboard compass)

SIDE PINS

This new presentation of the ArduPilotMega 2.6 system features all the same goodies as the predecessor, same CPU, same memory, same case, power module... but it comes without magnetometer on the main board (compass)
This sensor is moved to the GPS to allow less interference and more precision.
DJI NAZA V2 and GPS Combo Canada
DJI NAZA V2 and GPS Combo
Our Price: $599.99
Sale Price: $439.99
Savings: $160.00

(5)

The new Naza-M v2 Flight controller is here!
Tune your flying platform to the next level.

DJI impress again and show us the next innovation and improvement.
With the latest firmware, new altitude stabilization algorithm and optimized hardware structure, the Naza-M V2 provides better flight performance. The innovative All-in-one design simplifies installation and saves space and weight. It contains inner damping, controllers, 3-axis gyroscope, 3-axis accelerometer and barometer in its light and small Main Controller. It can measure flying altitude and attitude and therefore can be used for autopilot/automatic control.